The first thing to do in building your HDTV antenna is to make the elements. Take the 6ga. copper wire and cut 20 pieces each 18” in length. Then take a #8 Stainless screw and wrap the center of the wire around the screw as shown in the photo below:
This is one half of one element. By the way, I chose to use 6 ga. wire for the hdtv antenna elements because I want my hdtv antenna to survive high winds. Originally I tried using 14 ga wire, but the elements bent at approximately 35 MPH. This is actually a pretty simple test. I Just mocked up an element and mounted it on a board or something and just drove down the road and stuck the mocked up HDTV element out the window. (Disclaimer: safety first! This must only be done by trained professionals!)
Since I am using 6 ga. wire for my HDTV antenna, it is next to impossible to tightly wrap the wire around the screw. In order to get a snug fit, I used a pair of vice grips to complete the task as shown in the photo below:
Lillian Patterson says
I cut cable about two years ago and made an antenna (inside) similar to the one posts using copper wire as clothes hangers attached . on a thin piece of wood . I am able to get 39 channels. It truly worked better than the Purchased antenna.When my grandson saw how well it worked he was amazed and had that can you make me one on his face. Now that I see your model , I’m wondering if I up grade mine with wire and pipe as yours if it may be more effective.
WB8ERJ says
Hello,
The more elements that the antenna has the more gain it will have. Which will allow you a greater range. So if your antenna you built has less elements than mine, then adding elements will increase the gain of the antenna and will increase its range.
Good luck!
— Mike WB8ERJ
Brad Aliff says
How did you mount to your roof
WB8ERJ says
Hello,
I have a 30 foot tower that I mounted it on.
Len kearney says
would this work in an attic?
B
WB8ERJ says
Yes, but not as good as if it was outside. This antenna is somewhat tall. Something close to 8 feet.
Good luck!
Lawrence Smith says
Where’s the wire going to the TV set?
WB8ERJ says
Ah! Good question! It seems that I didn’t put in the text on page 7. If you look at the diagram showing the layout of the phasing harness, in the center is a black dot. That is where you connect the feed point, which is 300 ohms. Since most people use coax (recommended..) you will need to connect a CATV transformer. Otherwise known as a CATV balun. Then run your Coax down to the TV.
Good catch! I will update page 7 to properly answer your question.
— Mike WB8ERJ
Rick says
Any chance you could provide a picture of the balun connection? Is a simple 75 to 300 Ohm transformer (like this: https://www.parts-express.com/75-to-300-Ohm-Matching-Transformer-180-010?quantity=1) what you used? Where did you source the animal fencing?
WB8ERJ says
Hello,
Sorry, I don’t have a picture of the balun connection. Yes, the balun is a simple 75 to 300 ohm transformer like the one you link. They can be found pretty much anywhere. Walmart, Home Depot etc.
As far as the fencing, I picked min up at Tractor Supply. Any farm type supply stor will have it.
StephenH says
Does this pick up both VHF and UHF frequencies? What sort of gain do you observe with VHF and with UHF frequencies?
WB8ERJ says
Since the move to HDTV, all TV channels are UHF even though the old VHF channels kept their original channel numbers.
As far as gain observed, I have no way of measuring TV antenna gain. What I can tell you is that my HDTV antenna is on top of a 30 foot tower and I get a clear picture from several stations 70 miles away.
Hope this helps! — Mike
Jan Vandervliet says
I’m very interested in the antenna since analog tv broadcasts have ended in my country.
But ‘imperial’ sizes are as good as unknown in Europe.
Okay I know 1 inch = 1 thumb and equals 3,54 cm
1 ft = 30,48 cm
more difficult is the thickness of the copper wire, so what is ‘ga’ ?
The balun or transformer seems difficult to find here, how does it look like ?
Who helps ?
WB8ERJ says
Hello, thanks for reading my blog.
First of all, 1 inch = 2.54 cm instead of 3.54 cm like you mentioned. My guess is its just a mis-typing, but I wanted to be clear.
You make a good point about Imperial sizes, especially about wire size. Below I have listed the wire diameters in mm for you.
6ga wire = 4.11 mm
14ga wire = 1.63 mm
These wire sizes aren’t critical. The main reason for using the 4.11 mm wire for the elements is so it can withstand high winds without bending.
As far as the balun, here is an amazon link with a photo and a description – the balun needs to be UHF frequency range.
https://www.amazon.com/Philmore-Outdoor-Antenna-Matching-Transformer/dp/B01B1VSCK6
Hope this helps! Good luck!
— Mike WB8ERJ
Stephen Houska says
This design seems directional. I live in the middle of towers that are about the same distance apart. Linn Creek, MO 65052. Is there something you can recommend that is multi directional or can I put the same design on the backside of the reflectors?
Thanks for your time Stephen Houska.
WB8ERJ says
Hello, yes, this is very directional. In order to pick up stations from different directions you will need an antenna rotor to rotate in the direction of the station you want to receive.